Fluke Corporation MET/CAL Procedure ============================================================================= INSTRUMENT: Fluke 8600A: CAL ADJ /5500 DATE: 27-Jan-95 AUTHOR: Fluke Corporation REVISION: $Revision: 1.2 $ ADJUSTMENT THRESHOLD: 70% NUMBER OF TESTS: 1 NUMBER OF LINES: 127 CONFIGURATION: Fluke 5500A ============================================================================= # # Source: # Fluke 8600A manual # # Compatibility: # 5500/CAL 4.0 or MET/CAL 4.0 or later # # Subprocedures: # None # # Required Files: # None # # System Specifications: # TUR calculation is based on specification interval of the accuracy file. # The default 5500A accuracy file contains 90 day specs. # # Fluke makes no warranty, expressed or implied, as to the fitness # or suitability of this procedure in the customer's application. # # The 90 day specifications of the 5500A are used in TUR computations. # STEP FSC RANGE NOMINAL TOLERANCE MOD1 MOD2 3 4 CON 1.001 ASK- W 1.002 HEAD PRELIMINARY INSTRUCTIONS 1.003 DISP [32] WARNING 1.003 DISP HIGH VOLTAGE is used or exposed during the performance 1.003 DISP of this calibration. DEATH ON CONTACT may result if 1.003 DISP personnel fail to observe safety precautions. 1.004 DISP Before performing adjustments allow the UUT to stabilize 1.004 DISP (5 min.) at 23+/-5degC. Humidity less than 80%. 1.005 DISP Remove the cover from the UUT. 1.005 DISP Turn the UUT ON and allow it to warm up for 15 minutes. 1.006 HEAD DC VOLTAGE CALIBRATION ADJUSTMENT 1.007 RNG 200mV 1.008 DISP Connect a 1 MOhm resistor between the UUT V-Ohm 1.008 DISP HI and LO terminals. 1.009 DISP Adjust C24 for a UUT reading of 00.00+/-0.01mV 1.010 DISP Remove the resistor. 1.011 DISP Connect the 5500A and UUT as follows: 1.011 DISP [32] 5500A NORMAL HI to UUT V-Ohm HI 1.011 DISP [32] 5500A NORMAL LO to UUT V-Ohm LO 1.012 5500 190.00mV S 2W 1.013 MEMI Enter UUT reading in millivolts: 1.014 MATH M[1] = MEM 1.015 5500 -190.00mV S 2W 1.016 MEMI Enter UUT reading in millivolts: 1.017 MATH MEM1 = MEM - (-1 * M[1]) 1.018 JMPZ 1.022 0.01U 1.019 MATH MEM = M[1] 1.020 DISP Adjust C30 for a UUT reading of [MEM]+/-0.01mV. 1.021 JMP 1.012 1.022 5500 * S 1.023 RNG 2V 1.024 5500 1.9000V S 2W 1.025 DISP Adjust R57 for a reading of 1.9000V or 1.9001V. 1.026 5500 -1.9000V S 2W 1.027 DISP Adjust R57 for a reading of -1.9000V or -1.9001V. 1.028 5500 * S 1.029 RNG 20V 1.030 5500 19.000V S 2W 1.031 DISP Adjust R4 for a reading of 19.000+/-0.001V. 1.032 5500 -19.000V S 2W 1.033 DISP Adjust R4 for a reading of -19.000+/-0.001V. 1.034 5500 * S 1.035 RNG 200V 1.036 5500 190.00V S 2W 1.037 DISP Adjust R6 for a reading of 190.00+/-0.01V. 1.038 5500 * S 1.039 RNG 1200V 1.040 5500 1000.0V S 2W 1.041 DISP Adjust R8 for a reading of 1000.0+/-0.1V. 1.042 5500 * S 1.043 HEAD OHMS CALIBRATION ADJUSTMENT 1.044 RNG 2000kZ 1.045 5500 1000.0kZ S 2W 1.046 DISP Adjust R21 for a reading of 1000.0+/-0.1 kOhm. 1.047 5500 * S 1.048 DISP Connect the 5500A and UUT as follows: 1.048 DISP [32] 5500A NORMAL HI to UUT V-Ohm HI 1.048 DISP [32] 5500A NORMAL LO to UUT V-Ohm LO 1.048 DISP [32] 5500A AUX HI to UUT V-Ohm HI 1.048 DISP [32] 5500A AUX LO to UUT V-Ohm LO 1.049 RNG 2kZ 1.050 5500 1.0000kZ S CW 1.051 DISP Adjust R27 for a reading of 1.0000+/-0.0001 kOhm. 1.052 5500 * S 1.053 DISP Connect the 5500A and UUT as follows: 1.053 DISP [32] 5500A NORMAL HI to UUT V-Ohm HI 1.053 DISP [32] 5500A NORMAL LO to UUT V-Ohm LO 1.054 RNG 20MZ 1.055 5500 10.000MZ S 2W 1.056 DISP Adjust R29 for a reading of 10.000+/-0.003 MOhm. 1.057 5500 * S 1.058 HEAD AC VOLTAGE CALIBRATION ADJUSTMENT 1.059 DISP Simultaneously press the ACMA and DCV function switches. 1.060 RNG 1200V 1.061 DISP Adjust R72 for a reading of -20.0 to -30.0 1.062 5500 * S 1.063 RNG 2V AC 1.064 5500 1.9000V 500H SI S 2W 1.065 DISP Adjust R50 for a reading of 1.9000+/-0.0001V 1.066 5500 * S 1.067 RNG 200V AC # Adjustment at 20kHz instead of 50kHz. 1.068 5500 190.00V 20kH SI S 2W 1.069 DISP Adjust C2 for a reading of 190.00+/-0.05V 1.070 5500 * S 1.071 RNG 2V AC 1.072 5500 1.9000V 50kH SI S 2W 1.073 DISP Adjust C19 for a reading of 1.9000+/-0.0005V 1.074 5500 * S 1.075 RNG 20V AC 1.076 5500 19.000V 50kH SI S 2W 1.077 DISP Adjust C10 for a reading of 19.000+/-0.010V 1.078 END